резервуар майнкрафт immersive engineering

Immersive Engineering/Резервуар

Резервуар — многоблочная структура добавляемая модификацией Immersive Engineering, позволяет удобно хранить жидкости в больших объемах. Вмещает в себя до 512 вёдер любой жидкости.

Жидкость можно заливать и забирать из резервуара с помощью ведра из любой стороны, заливать через верхний и нижний выход, а забирать только через нижний. Одновременно резервуар может хранить только один тип жидкости.

Постройка

Схема постройки резервуара
Слой 5 Слой 4 Слой 3 Слой 2 Слой 1

При разрушении подходящим инструментом из резервуара выпадает следующее:

Источник

Immersive Engineering/Резервуар

Резервуар — многоблочная структура добавляемая модификацией Immersive Engineering, позволяет удобно хранить жидкости в больших объемах. Вмещает в себя до 512 вёдер любой жидкости.

Жидкость можно заливать и забирать из резервуара с помощью ведра из любой стороны, заливать через верхний и нижний выход, а забирать только через нижний. Одновременно резервуар может хранить только один тип жидкости.

Постройка [ ]

Схема постройки резервуара
Слой 5 Слой 4 Слой 3 Слой 2 Слой 1

При разрушении подходящим инструментом из резервуара выпадает следующее:

Источник

Fluid Pump (Immersive Engineering)

This page is about the Fluid Pump added by Immersive Engineering. For other uses, see Fluid Pump .

The Fluid Pump is a block added by Immersive Engineering. It is used together with the Fluid Pipe to move liquids at faster speeds, into tanks without input/output, and to suck up liquids. The Fluid Pump is two blocks tall.

To use fluid containers (Tanks) without explicit input/output, the Fluid Pump can be configured to automatically pull (or push) from the fluid container. The base of the Fluid Pump should be configured: hitting a side with an Engineer’s Hammer will change the configuration of that side; doing so while sneaking will change the configuration of the side opposite the one hit. One blue dot is an input, one orange dot is an output, and no dot will not accept any liquids.

The Fluid Pump must be powered with a Redstone signal in order to function. The signal can be applied to any side other than the top or bottom.

Using a Fluid Pump instead of a Fluid Pipe can make liquid transfer five times faster. This is more useful for larger setups.

The last use of the Fluid Pump is for pumping out raw liquids, such as Lava. This, unlike the other functions, requires Redstone Flux (RF). RF should be input through the top side of the top block in the Fluid Pump. It will pull in liquids through its input side/sides.

When pumping raw liquids, certain liquids will be converted to other blocks; in particular Lava to Cobblestone. However, raw liquids will just disappear.

Gallery

A setup like this with plain Fluid Pipes will not work, since the OpenBlocks Tank does not have an explicit output.

This setup will move liquids from the OpenBlocks Tank to the Metal Barrel.

The Fluid Pump quickly moving liquids from the left Tank to the right Tank.

The Fluid Pump pumping Lava into the Tanks.

Источник

Immersive Engineering

Immersive Engineering is a mod created by users BluSunrize and Mr_Hazard. It adds a number of structures that create a more realistic setting for power generation using the RF system.

It is best known for its multiblock machines, characterized by their industrial look. Both single and multiblock machines operate on three tiers of power, low voltage being 256 RF/t, medium being 1024 RF/t and high corresponding to 4096 RF/t.

It was also compatible with IndustrialCraft 2 EU energy prior to Minecraft version 1.10.

The most important tool for this mod is the Engineer’s Manual, created by crafting together a book and a lever. It contains recipes and instructions for everything in the mod.

Источник

Fluid Pipe (Immersive Engineering)

This page is about the Fluid Pipe added by Immersive Engineering. For other uses, see Fluid Pipe .

The Fluid Pipe is a block added by Immersive Engineering. It is used to move liquids around.

The Fluid Pipe will automatically pull liquids from a liquid output side to put them into an input liquid side, as shown to the right. Right-clicking a Fluid Pipe with an Engineer’s Hammer in it’s connecting spot will prevent it from connecting, or allow it to connect if it has been disabled.

Fluid Pipes can be covered with a Scaffolding; such as a Treated Wood Scaffolding or a Steel Scaffolding. Scaffoldings can be used to climb Fluid Pipes, or simply for decoration.

The Fluid Pipe is fairly slow on its own; a Fluid Pump can be used to speed the Fluid Pipe at the cost of some Redstone Flux (RF).

Содержание

Gallery

Using Fluid Pipes to automate a Refinery. Note that the Metal Barrels must have their configurations set.

Using Fluid Pipes with Metal Barrels; note the configurations (the blue dot and the orange dot).

Источник